![]() When inserting it into the breakout board be sure to use proper personal grounding, such as a grounding wrist strap, to prevent damage the module.ġx FLIR Lepton® 2. The Radiometric Lepton module is extremely sensitive to electrostatic discharge (ESD). Note: This kit comes in two separate parts and will need to be assembled once received. The camera is interfaced with Raspberry Pi board with the help of FLIR Lepton Thermal Camera Breakout Board, which is a complete long-wave infrared (LWIR). A few things to consider about this kit: the breakout board will accept a 3-5V input and regulate it to what the Lepton® wants, to read an image from the lepton module all you need is an SPI port, and to configure the camera settings you also need an I2C port, although this is not required. Meanwhile, each breakout board in these kits provides the socket for the Lepton, power supply's, 25Mhz Crystal Oscillator, 100 mil header for use in a breadboard or wiring to any host system. The Lepton 2.5 can output a factory-calibrated temperature value for all 4800 pixels in a frame irrespective of the camera temperature with an accuracy of +/-5˚C. The Radiometric Lepton® LWIR module included in each Dev Kit acts as a sort of camera and packs a resolution of 80 × 60 active pixels into a camera body that is smaller than a dime and captures infrared radiation input in its nominal response wavelength band (from 8 to 14 microns) and outputs a uniform thermal image. FLIR Lepton Breakout Board V2.0 Regular price 59.99 USD Regular price Sale price 59.99 USD Unit price / per. Groupgets PT2 board or Lepton Breakout board, Lepton SDK or Lepton User App Watch EP 102: General Video and Command Interfacing, and register to access the entire series. All you need to do to get this kit set up, simply attach the Lepton® imager module into the provided breakout, connect the headers, and you will be seeing in full darkness in no time! FLIR Lepton breakout board for all versions, support VSYNC which was not supported by previous V1.4 Can be used with most computer platforms and custom. This kit includes a breakout as well as the Lepton® 2.5 longwave infrared (LWIR) imager. ![]() Features : LWIR sensor,wavelength 8 to 14 μm 51-deg HFOV, 63.Do you see what we see? With the FLIR Radiometric Lepton® Dev Kit you will be able to bring FLIR's thermal imaging reliability and power to your Arduino, Raspberry Pi, or any ARM based development tool all in an easy to access breadboard friendly package. Get a fully tested Shuttered Lepton Camera with a breakout board at. Breakout Boards Card Extenders Coating, Grease, Repair Drill Bits, End Mills Etching and Fabrication Equipment. The FLIR Lepton is the most compact longwave infrared (LWIR) sensor. Check stock and pricing, view product specifications, and order online. Meanwhile, each breakout board in these kits provides the socket for the Lepton®, power supply’s, 25Mhz Crystal Oscillator, 100 mil header for use in a breadboard or wiring to any host system. Order FLIR Lepton 500-0771-01 (500-0771-01-ND) at DigiKey. All you need to do to get this kit set up, simply attach the Lepton® imager module into the provided breakout, connect the headers, and you will be seeing in full darkness in no time! The Lepton® LWIR module included in each FLiR Dev Kit acts as a sort of camera and packs a resolution of 80 × 60 pixels into a camera body that is smaller than a dime and captures infrared radiation input in its nominal response wavelength band (from 8 to 14 microns) and outputs a uniform thermal image. With this kit you will be able to bring FLiR’s thermal imaging reliability and power to your Arduino, Raspberry Pi, or any ARM based development tool all in an easy to access breadboard friendly package. Features Compatible with Lepton 2.x and 3. It’s compatible with many low-cost ARM based evaluation boards, in addition it’s easy to connect to pin outs for Arduino or via short jumper wires to Raspberry Pi. Hello, Is there a recommended Camera for working w/ the FLIR Lepton v2 breakout Seth P.S. The FLiR Dev Kit includes a breakout as well as a Lepton® longwave infrared (LWIR) imager. The PureThermal Breakout Board is an easy to interface evaluation board used to quickly evaluate the FLIR Lepton® thermal camera modules. Numéro de l'objet: 332844981999 Lepton flir sensor and breakout board Thermal DIY camera.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |